AC Repair in Cache Valley, UT: How to Repair 3 Common Problems

There can be a couple of explanations why your AC equipment won’t start: a tripped circuit breaker, incorrect thermostat settings, a shut off switch or a full condensate drain pan.

Your system won’t start when you have a tripped breaker.

To find out if one has tripped, find your house’s main electrical panel. You can locate this metallic box on the wall in the basement, garage or closet.

• Ensure your hands and feet are free of moisture before you work on the panel or breakers.
• Find the breaker labeled “AC” and ensure it’s in the “on” location. If it’s tripped the lever will be in the middle or “off” position.
• Firmly move the lever back to the “on” spot. If it instantaneously triggers again, don’t touch it and get in touch with us at 435-753-5515. A breaker that keeps turning off may indicate your home has an electrical issue.

If your thermostat isn’t telling your air conditioner to work, it won’t activate.

The first point is checking it’s on “cool” and not “heat.” Otherwise your air conditioner might not turn on. Or you might get. hot air coming from vents being the heat is running instead.

If you rely on a regular thermostat:

• Put in new batteries if the readout is clear. If the screen is presenting jumbled numbers, buy a new thermostat.
• Check the proper option is showing. If you can’t update it, cancel it by decreasing the temperature and pressing the “hold” button. This will force your AC to work if the configuration is incorrect.
• Test setting the thermostat 5 degrees cooler than the room’s temperature. Your AC won’t cool if the thermostat is set the same as the room’s temperature.

Once your thermostat is set properly, you should begin getting chilled air quickly.

If you have a smart thermostat, such as one produced by Nest, Ecobee, Lux, Honeywell or Bosch, go to the manufacturer’s website for assistance. If you still can’t get it to work, reach us at 435-753-5515 for assistance.

Your AC usually has a shut-off lever near its outdoor unit. This switch is typically in a metal box hung on your residence. If your equipment has recently been worked on, the lever may have inadvertently been positioned in the “off” position.

Condensate drain pans catch the surplus water your AC pulls from the air. This pan can be positioned either beneath or inside your furnace or air handler.

When there’s an obstruction or clogged drain, water can build up and trigger a safety control to switch off your equipment.

If your pan has a PVC pipe or drain, you can get rid of the surplus water with a custom pan-cleaning tablet. You can purchase these capsules at a home improvement or hardware retailer.

If your pan has a pump, look for the float switch. If the mechanism is “up” and there’s liquid in the pan, you could need to get a new pump. Call us at 435-753-5515 for support.

If your equipment is on but not providing cold air, its airflow could be clogged. Or it might not have adequate refrigerant.

Your unit’s airflow can be reduced by a plugged air filter or dirty condenser.

A dusty filter can cause countless problems, like:

• Lower airflow
• Icy refrigerant lines or evaporator coil
• Inconsistent cooling
• Larger utility bills
• Making your system break down faster

We recommend installing new flat filters once a month, and accordion filters every three months.

If you can’t remember when you last installed a new one, turn off your system totally and remove the filter. You can find the filter in your furnace or air pump’s blower compartment. It could also be located in a connected filter case or wall-mounted return air grille.

Hold the filter up to your light fixture. If you can’t see any light you certainly should replace it.

Weeds, vegetation and sticks can get in the way of your condensing system. This can limit its airflow, impact its energy efficiency and change your comfort. Here’s how you can get your unit running properly again.

1. Shut off the electrical current totally at the breaker or outdoor lever.
2. Clear yard waste around the air conditioner. Once you’ve removed all the refuse within a two-foot radius, you can use a fine-bristled brush or vacuum to slowly clean the condenser fins. Warped fins can also hurt effectiveness, so you can attempt to reshape them with a blunt knife.
3. Use a hose nozzle to gingerly take off dirt on the fins from inside the unit. Don’t get liquid on the fan motor.
4. Put the top back on and turn on the power.

When air conditioning systems don’t have ample refrigerant, they’ll have to work much harder to remove heat and humidity from the air.

Here are a few indications that your equipment is leaking refrigerant:

1. It takes too long to lower the temperature in your residence and you’re continually decreasing the temperature on the thermostat.
2. Cooling coming through the ducts isn’t as chilled as it should be.
3. You’re experiencing fizzing or gurgling noises when cooling works.
4. Your evaporator coil is frosty as a result of having trouble handling heat.

Worried your system is seeping refrigerant? You need a qualified heating and cooling service specialist to fix the leak and refill the right level of refrigerant in your equipment. Reach us at 435-753-5515 for assistance.

When it feels like you’re not getting adequate amounts of cool air, there’s usually a blockage or separation within your AC system.

• The initial stage is checking your air filter. Buy a new one if it’s dirty.
• Then ensure the registers are open around your house.
• If you’re still not getting ample cold air, you should have your ducts inspected by a expert like Western Mechanical, Inc.. Your ducts might need to be fixed or relinked in limited space spots like your attic, basement or crawl space.